Brake cleaning tips

Post Reply
User avatar
al
Mass Debater
Posts: 4768
Joined: Wed Sep 05, 2001 1:00 am
Current Ride: Space Hopper
Location: Uranus
Contact:

Brake cleaning tips

Post by al »

Like me, some of you have been using your bike on and off during the winter and may have noticed a slow degradation in brake performance or the bike needing more effort to wheel around. You might notice this even if you have had your bike in storage over the winter months and go to get it out of hibernation in the spring.

If so, it's time to give the calipers a bit of a clean. The following is my own personal method so feel free to find a method that works for you.

Along side my trusty tool box, I look out the following items for this task:-
  • 1 tub of cotton buds / q-tips
  • 1 small container of brake fluid labelled "for brake cleaning only"
  • 1 pair of plumbers pliers/G-clamp or similar.
  • 1 handfull of rags
  • 1 box of nitrile gloves (to protect my soft hands from nasty chemicals)
  • 1 aerosol can of brake cleaner
  • 1 spare spanner with a body longer than your brake pads and a similar thickness to your disks (degrease spanner with brake cleaner before use)
Only remove one caliper at a time and if you have 4 pot brakes then some sort of g-clamp or similar is handy for preventing the pistons you are not working on extending too far.

With the caliper removed I first slide the pads away from the piston(s) then give them a blast with some brake cleaner spray to remove any loose dirt.

Then slide the pads back out to the sides and place the clean spanner between the pads. Carefully and slowly pump the brake lever to extend the piston(s) a couple of mm. The spanner is only there to prevent you accidently over extending the pistons and should not be squeezed hard by the pads.

Working one piston at a time, dip a clean cotton bud into the brake fluid and gently clean the exposed sides of the pistons. At this time you may want to remove the pads to give better access all around the pistons.

Once you have cleaned the pistons with the brake fluid and cotton buds then give them a quick blast with the brake cleaner spray again to remove any excess brake fluid. At this point I would probably recommend popping the pads back in place before attempting to push the pistons back into the calipers.

Depending on how easy your pistons are to move you may be ably to just twist the spanner inbetween the pads to put enough pressure on the pads to retract into the caliper. If not that's when you may have to use the plumbers pliers with the ends wrapped in rags to "ease" the pistons back into the body of the caliper.

If you have sliding type calipers such as the one shown below then you want to make sure that the caliper is free to move along the slide pins. (a sliding caliper will only have piston(s) one one side of the caliper)

Image

The metal part on the right hand side of the rubber gaiters/boots should slide from side to side with finger tip pressure. If it doesn't then possibly one or both of the gaiters has failed allowing muck and salt inside which builds up on the slider causing friction. However, the more likely problem is that salt and muck that has got between the bottom gaiter and the hole in the caliper body that the gaiter/boot passes through. Water carries the salt and grime into the space where it dries out and crystalises effectivly reducing the diameter of the hole in the caliper which causes the rubber of the gaiter/boot to press on the sliding pin making it hard to move.

The only choice you have there is to carefully remove the gaiter/boot and clean up it and all the muck from inside it's mounting hole as per the photo below.

Image

Once cleaned up you can then carefully replace the gaiter (easier said than done so take your time). I carefully use some ACF-50 on the rubber to lubricate it and neutralise any remaining salt and apply ACF-50 to the corresponding hole in the caliper body..

Then all is left is to replace the slider, pads, and re-attach the calliper. Please remember to install the pads the correct way round with the friction material of each pad pointing together!!!!!!

Remember to pump your brake levers and test the brakes before riding and your brakes should be working properly again.

At any time of year, if you find that your brakes are betting a bit spongy then I would recommend cleaning your pistons and making sure they are all free to move before people start going on about changing brake lines etc. If your pistons aren't free to move then what good are braided lines going to be except an additional expence!

Big Kneed Al (master of the emergency stop & "stand up" comedian).
mpgscott
Direct Access
Posts: 23
Joined: Tue May 08, 2007 8:14 am

Re: Brake cleaning tips

Post by mpgscott »

Cracking write up cheers..
User avatar
Dave
Enjoys a nice shaft!
Posts: 2160
Joined: Fri Dec 12, 2003 8:24 am
Current Ride: Big sensible pretty bikes with big smooth tyres,
Small bikes with small lumpy tyres and a truck with HUGE lumpy tyres !
Location: Red Dwarf
Contact:

Re: Brake cleaning tips

Post by Dave »

mpgscott wrote:Cracking write up cheers..
:2up

I make sure I wear glasses when using break cleaner, it can have a good bit of pressure and blast back into your face.
User avatar
aisgsimon
Knee Flapper
Posts: 274
Joined: Sun Sep 05, 2010 10:35 pm
Current Ride: '88 VFR 750FJ

Re: Brake cleaning tips

Post by aisgsimon »

great advice!
User avatar
Big Little Dave
Tinky Winky
Posts: 456
Joined: Thu Oct 08, 2009 4:07 pm
Current Ride: 2011 CB1000R

Re: Brake cleaning tips

Post by Big Little Dave »

I also use GT85 or WD40 to polish my bike, but after I use it on the brakes my bike struggles to stop when I apply them :confused Any ideas why...
User avatar
The Rossi Kid
Make way for Noddy
Posts: 1765
Joined: Thu Aug 05, 2004 3:08 pm
Location: For you to know and me to find out

Re: Brake cleaning tips

Post by The Rossi Kid »

Big Little Dave wrote:I also use GT85 or WD40 to polish my bike, but after I use it on the brakes my bike struggles to stop when I apply them :confused Any ideas why...
:-o:???:


Sent from my HTC Desire S using Tapatalk 2
User avatar
Zathos
Mr Magpie
Posts: 3161
Joined: Sun Apr 27, 2003 10:46 pm
Current Ride: Aprilia Tuono Factory R
Location: Everywhere & Nowhere

Re: Brake cleaning tips

Post by Zathos »

Big Little Dave wrote:I also use GT85 or WD40 to polish my bike, but after I use it on the brakes my bike struggles to stop when I apply them :confused Any ideas why...

Ronz MK2 ;)
User avatar
Gazza
I don't believe it!
Posts: 2475
Joined: Mon Sep 10, 2001 1:00 am
Current Ride: KTM 690 Duke
Location: Sconny Botland

Re: Brake cleaning tips

Post by Gazza »

He has to be winding us up.

There can only be one Ronz
User avatar
The Rossi Kid
Make way for Noddy
Posts: 1765
Joined: Thu Aug 05, 2004 3:08 pm
Location: For you to know and me to find out

Re: Brake cleaning tips

Post by The Rossi Kid »

If it isn't a wind up then I hope Keith is bitch slapping him around the garage right now!

Sent from my HTC Desire S using Tapatalk 2
User avatar
al
Mass Debater
Posts: 4768
Joined: Wed Sep 05, 2001 1:00 am
Current Ride: Space Hopper
Location: Uranus
Contact:

Re: Brake cleaning tips

Post by al »

Gazza wrote:He has to be winding us up.

There can only be one Ronz
Izinbard used to spray WD40 on his disks. Does that make 3 Ronz'z :eek
User avatar
haiax0
Tank Slapper
Posts: 680
Joined: Mon Mar 14, 2011 2:04 pm
Current Ride: Ducati Hypermotard
Location: Somewhere near the fridge...

Re: Brake cleaning tips

Post by haiax0 »

Nice write up!

Lubing up your brakes... Seems legit Dave haha!


Sent from my Ipap using Tapatalk HD
User avatar
Big Little Dave
Tinky Winky
Posts: 456
Joined: Thu Oct 08, 2009 4:07 pm
Current Ride: 2011 CB1000R

Re: Brake cleaning tips

Post by Big Little Dave »

The Rossi Kid wrote:If it isn't a wind up then I hope Keith is bitch slapping him around the garage right now!

Sent from my HTC Desire S using Tapatalk 2

Of course its a wind up! My dad would never let me put that stuff on my discs, unless he wanted to get rid of me :eek Now theres a thought!

:log :log
User avatar
al
Mass Debater
Posts: 4768
Joined: Wed Sep 05, 2001 1:00 am
Current Ride: Space Hopper
Location: Uranus
Contact:

Re: Brake cleaning tips

Post by al »

I had a brake cleaning session yesterday so thought I would bump this post as it's that time of year.

Although I had been regularly cleaning my calopers and pistons over the winter, as in my post above, the salt and muck had managed to get between the rubber gator of one of the slider pins and the body of the caliper effectivly squeezing the rubber against the pin and gripping it solid.

This would explain why the bike felt like it had a flat tyre when riding and pushing it around. :oops

All sorted now.

Big Kneed Al (master of the emergency stop & "stand up" comedian).
User avatar
RK6
Would you like a mushroom?
Posts: 1508
Joined: Thu Feb 01, 2007 2:30 pm
Current Ride: Hypermotard SP
Location: Aberdeen

Re: Brake cleaning tips

Post by RK6 »

Excellent guide Big Kneed Al (master of the emergency stop & "stand up" comedian). :worthy
User avatar
Gazza
I don't believe it!
Posts: 2475
Joined: Mon Sep 10, 2001 1:00 am
Current Ride: KTM 690 Duke
Location: Sconny Botland

Re: Brake cleaning tips

Post by Gazza »

Haven't needed to do this for a while obviously, but after a ride on salty roads I would clean the bike with a jet wash. I'd then give the brakes a good blast and ride slowly up and down the road with the brakes applied to boil off the excess water before storage. Storage was in a heated, dehumidified garage. Never had a problem with sticky brakes whilst doing that.

I'm having another large garage built in the garden this summer and it'll be fully insulated and heated etc for cars and bikes during the cold months. A dehumidifier is important or all that moist air in a warm garage will rust up your goodies.
User avatar
Dave
Enjoys a nice shaft!
Posts: 2160
Joined: Fri Dec 12, 2003 8:24 am
Current Ride: Big sensible pretty bikes with big smooth tyres,
Small bikes with small lumpy tyres and a truck with HUGE lumpy tyres !
Location: Red Dwarf
Contact:

Re: Brake cleaning tips

Post by Dave »

Gazza wrote: Wed Apr 19, 2017 5:40 pm A dehumidifier is important or all that moist air in a warm garage will rust up your goodies.
I recently got a dehumidifier, it pulls about a litre of water a day out of the air in the garage
User avatar
RK6
Would you like a mushroom?
Posts: 1508
Joined: Thu Feb 01, 2007 2:30 pm
Current Ride: Hypermotard SP
Location: Aberdeen

Re: Brake cleaning tips

Post by RK6 »

I really should buy a dehumidifier. Especially now that I've got a brew setup in my garage. :log

At the risk of going slightly off topic, can either of you guys recommend a good one?
User avatar
Gazza
I don't believe it!
Posts: 2475
Joined: Mon Sep 10, 2001 1:00 am
Current Ride: KTM 690 Duke
Location: Sconny Botland

Re: Brake cleaning tips

Post by Gazza »

RK6 wrote: Thu Apr 20, 2017 2:05 pm I really should buy a dehumidifier. Especially now that I've got a brew setup in my garage. :log

At the risk of going slightly off topic, can either of you guys recommend a good one?
I haven't had one for 10 years. But Google is your friend...


https://www.bestspy.co.uk/dehumidifiers/
User avatar
al
Mass Debater
Posts: 4768
Joined: Wed Sep 05, 2001 1:00 am
Current Ride: Space Hopper
Location: Uranus
Contact:

Re: Brake cleaning tips

Post by al »

My back brake has been feeling wooden and a bit crap for a while now. I cleaned up the rear caliper over the Christmas period so thought it couldn't be needing more TLC already.

This afternoon, when I went out to my bike after work, I noticed that the brake light was on. After playing with the front and rear brakes I found out what the problem was. The rear brake lever was almost completely seized so when I was applying it it was staying on.

The rear brake lever has now been stripped, cleaned re-greased, assembled and tested and everything is alright in the world again. The only difficult bit was removing and refitting the circlip holding the lever onto the plain bearing shaft.

Therefore add checking all moving parts of the brake system to your maintenance routine and not just the calipers!

Big Kneed Al (master of the emergency stop & "stand up" comedian).
Post Reply