AberdeenBikers

I have decided to get a paint jobby done on my R.6. Mike Stuart is doing the job and I have decided to go for a Rossi Rep, but red rather than blue. See below


I got the wheels off today, so I popped in past Mr Sillets and got the rubber removed then dropped the wheels off at Finesse to get powdercoated white. I should get my wheels back next Friday. So today I went on a mad spending spree. Cush drive rubbers needed replaced, so got a set off ebay for £26.00. I have decided against putting rim tape on so I bought wheel decals (all red letter, but the "R" will be black)


I found a really good website for bearings http://www.bikebearings.co.uk full bearing kit for £46.00. I have decided to keep my original seat cowl so I bought a new one from powerbronze for £62.99. Mike is going to service the bike so I was looking for a service kit got K&N Air & Oil Filter off ebay for £54.00, fuel filter for £6.00 and 4 x NGK iridium ix spark plugs for £18.00 again off ebay. So hopefully the bike will be ready by the end of the month

Yamahahaha wrote:4 x NGK iridium ix spark plugs for £18.00 again off ebay.

The ebay spark plug factory

Gazza wrote:

Yamahahaha wrote:4 x NGK iridium ix spark plugs for £18.00 again off ebay.

The ebay spark plug factory

Busy place, I noticed the QHSE Manager is missing

White wheels? To much effort to keep clean!

Grant wrote:White wheels? To much effort to keep clean!

As you said I am loaded, so I will pay someone to do it!!!

Please, don't put Arr Waan rim logo's on, if you have an R-6.

Coddy wrote:Please, don't put Arr Waan rim tape on, if you have an R-6.

The pic was an example. I have requested r.6 all red, but the "R" black, should look better than rim tape.

Should look good in red, but for me, i would change the FIAT logo for something else.
Don't like the look of a car logo on a bike, but it's your bike.

Sound's like it's going to look the part, the red does look nice, will one be getting a matching lid.

Flamedamper wrote:Sound's like it's going to look the part, the red does look nice, will one be getting a matching lid.

No keeping the same lid.

Update
Ordered the bearings on Monday and they arrived on Wednesday, very good service. Two items arrived today, fuel filter & cush drive rubbers very unusually as they came from eBay (user - bikebusiness). So just waiting for the filters and rim stickers to arrive. I also bought clear headlight lens covers as my headlight have a few scrapes, again off eBay.

i think your bike will look pretty decent when its all rebuilt dude

all the best with your project

JT52 wrote:i think your bike will look pretty decent when its all rebuilt dude

all the best with your project

Cheers JT. Just looking forward to seeing the finished article. I wanted something different, so rather than the usual blue rossi rep I wanted it red. I can't see many having the same paint job.

http://cgi.ebay.co.uk/Yamaha-YZF-R1-FIA ... 51904bba3d

should look good going by this one

splattercash wrote:http://cgi.ebay.co.uk/Yamaha-YZF-R1-FIA ... 51904bba3d

should look good going by this one

Very nice.

Spark plugs arrived today. Just waiting for the air & oil filter, clear headlight covers & new foot pegs.

K&N Air & Oil Filters arrived today, also wheel decals & headlight lens covers. Finesse phoned to say the wheels are ready, so picked them up and dropped them off at Mike's to get the new bearings fitted. Once the new bearings are in and the brake disc's are back on its then down to Mr Sillet to get my rubbers back on. Once the wheels are back on the bike the paint jobby will begin.

You need some red braided brake lines like the one on Ebay!

Grant wrote:You need some red braided brake lines like the one on Ebay!

The bike already had braided hoses, silver. Can you get covers???

Yamahahaha.
I used Finesse years ago to get a swing arm powder coated a silver gray colour. They did a superb job but the colour I thought was a bit flat.
How did your white wheels turn out ?
I'll be getting mine done the same colour as yours and am wondering how they'll look.
(Didn't bag off the brake line when I took the caliper offshore with me for a rebuild. Fluid on the rim for 3 weeks and you'll guess what happened next )

What did Finesse charge you for both wheels ?

crankcase wrote:Yamahahaha.
I used Finesse years ago to get a swing arm powder coated a silver gray colour. They did a superb job but the colour I thought was a bit flat.
How did your white wheels turn out ?
I'll be getting mine done the same colour as yours and am wondering how they'll look.
(Didn't bag off the brake line when I took the caliper offshore with me for a rebuild. Fluid on the rim for 3 weeks and you'll guess what happened next )

What did Finesse charge you for both wheels ?

Wheels look really good. They charged me £110 for 2 wheels and the hub carrier.

Cheers min

crankcase wrote:Cheers min

Get your bearings from http://www.bikebearings.co.uk mucho cheapo

Wheels have been rebuilt, so off to Mr Sillets to get my rubbers back on. Once the wheels are back on the bike the painting will begin. Should have a painted bike by next week, hopefully.

Yamahahaha wrote:

crankcase wrote:Cheers min

Get your bearings from http://www.bikebearings.co.uk mucho cheapo

Ye I had a look at your link. Your supplying good info here min
I'll be getting prices from there whenever I come to do the wheels. Nae idea when that'll be. Probably next winter but the bike will still be used this year. (Hope AberdeenBikers keep it slow for me on the viffer when I make my inaugural run)
I got one of the swing arm bearings from Scott bearings in Aberdeen. Can't remember how much it was but will probably get prices there too.
The other bearing was a non standard size (good old Honda ) and I ordered it through McGowans.
Again can't remember how much but do remember thinking OUCH.

Get some of that paint protection film for the leading edges of your fairings. I had a bike that was painted and it chipped like a MOFO. A lot more than normal.

Not a race rep fan myself (although I did own one ) but it should look tidy from what youve said. At least there wont be another on the go....you hope.